Firmware v1.7.1

What's Changed

• Switched to using Pico-SDK v2.0.0
• Preliminary support for using Pico 2
• Home Assistant MQTT Discovery Support
• Support for VSENSORs in MQTT client.
• New I2C Sensors supported:
  • Support for LPS22 and LPS25 pressure sensors
  • Support for SHTC3 temperature and humidity sensor
• New configuration commands:
  • MEASure:VSENSORS?
  • MEASure:VSENSORx:HUMidity?
  • MEASure:VSENSORx:PREssure?
  • SYS:MQTT:HA:DISCovery
  • SYS:MQTT:HA:DISCovery?
  • SYS:MQTT:INT:VSENSOR
  • SYS:MQTT:INT:VSENSOR?
  • SYS:MQTT:MASK:VTEMP
  • SYS:MQTT:MASK:VTEMP?
  • SYS:MQTT:MASK:VHUM
  • SYS:MQTT:MASK:VHUM?
  • SYS:MQTT:MASK:VPRE
  • SYS:MQTT:MASK:VPRE?
  • SYS:MQTT:TOPIC:VTEMP
  • SYS:MQTT:TOPIC:VTEMP?
  • SYS:MQTT:TOPIC:VHUM
  • SYS:MQTT:TOPIC:VHUM?
  • SYS:MQTT:TOPIC:VPRE
  • SYS:MQTT:TOPIC:VPRE?

Full Changelog: v1.7.0...v1.7.1

Firmware v1.7.0

What's Changed

• Support for a new board model: 0401D
• Support for 1-Wire temperature sensors:
  • DS18S20
  • DS18B20 / MAX31280
  • DS1822
  • DS1825 / MAX32826
  • DS28EA00
• Support for I2C temperature sensors:
  • ADT7410
  • AHT1x (AHT10, AHT11 ,...)
  • AHT2x (AHT20, AHT21 ,...)
  • AS621x (AS6212, AS6214, AS6218)
  • BMP180
  • BMP280
  • DPS310
  • MCP9808
  • PCT2075
  • STTS22H
  • TMP102
  • TMP117
• New configuration commands:
  • CONF:FANx:HYST:TACHO
  • CONF:FANx:HYST:TACHO?
  • CONF:FANx:HYST:PWM
  • CONF:FANx:HYST:PWM?
  • SYS:I2C?
  • SYS:I2C:SCAN?
  • SYS:I2C:SPEED
  • SYS:I2C:SPEED?
  • SYS:ONEWIRE
  • SYS:ONEWIRE?
  • SYS:ONEWIRE:SENSORS?
  • SYS:VREFadc
  • SYS:VREFadc?
  • SYS:VSENSORS:SOURCES?

Full Changelog: v1.6.3...v1.7.0

Firmware v1.6.3

What's Changed

• Initial support for Locked Rotor Alarm fans.
• New commands:
  • CONF:FANx:RPMMODE
  • CONF:FANx:RPMMODE?
  • CONF:MBFANx:RPMMODE
  • CONF:MBFANx:RPMMODE

Full Changelog: v1.6.2...v1.6.3

Firmware v1.6.2

What's Changed

• Fix possible hang during boot (introduced in v1.6.1 firmware) if flash filesystem needed to be initialized.
• New command:
  • SYS:LFS:FORMAT

Full Changelog: v1.6.1...v1.6.2

Firmware v1.6.1

What's Changed

• Add Telnet support.
• Switch to using pico-lfs library for littlefs.
• Add support for mixing sensors and vsensors as source for VSENSORs.

Full Changelog: v1.6.0...v1.6.1

Firmware v1.6.0

What's Changed

• Add MQTT support (new commands under SYS:MQTT:)
• Add HTTPS support
• Preserve RTC clock on soft reset.
• New commands:
  • SYS:FLASH?
  • SYS:MEM
  • SYS:MEM?
  • SYS:LFS?
  • SYS:TLS:CERT
  • SYS:TLS:CERT?
  • SYS:TLS:PKEY
  • SYS:TLS:PKEY?

Full Changelog: v1.5.2...v1.6.0

Firmware v1.5.2

What's Changed

• Support for "calculated" MBFAN tacho signals. by @tjko in #59

  • Support new "sources" for MBFAN tachometer signals:
    • MIN (lowest fan speed of a groups of fans)
    • MAX (fastest fan speed of a group of fans)
    • AVG (average fan speed of a group of fans)

  (see CONF:MBFANx:SOURCE documentation)

• Add commands to manually set timezone. by @tjko in #60

  • New commands:
    • SYS:TIMEZONE
    • SYS:TIMEZONE?

Full Changelog: v1.5.1...v1.5.2

Firmware v1.5.1

What's Changed

• Add support for custom (LCD) boot logo. by @tjko (more info in wiki)
• Bugfix for when temperature sensor reading exceeds highest mapped value in temperature map. by @physcon in #56
• Lower default SPI bus speed from 48MHz to 30MHz

Full Changelog: v1.5.0...v1.5.1

Firmware v1.5.0

What's Changed

• Virtual sensor (vsensor) support added.
• Support for custom layout on OLED screens.
• Update to use Pico-SDK v1.5.1
• New commands:
  • CONFigure:VSENSORx:NAME
  • CONFigure:VSENSORx:NAME?
  • CONFigure:VSENSORx:SOUrce
  • CONFigure:VSENSORx:SOUrce?
  • CONFigure:VSENSORx:TEMPMap
  • CONFigure:VSENSORx:TEMPMap?
  • CONFigure:VSENSORx:FILTER
  • CONFigure:VSENSORx:FILTER?
  • MEASure:VSENSORx?
  • MEASure:VSENSORx:Read?
  • MEASure:VSENSORx:TEMP?
  • WRIte:VSENSORx
  • SYStem:DISPlay:LAYOUTR
  • SYStem:DISPlay:LAYOUTR?
  • SYStem:WIFI:MODE

Full Changelog: v1.4.1...v1.5.0

Firmware v1.4.1

What's Changed

• Small updates to default theme and OLED display layout
• New command SYS:TIME
• Add rounding of numbers in JSON output (to match CSV output)

Full Changelog: v1.4.0...v1.4.1